Deck Removal To Get At Fuel Tank

Not sure how you aim to glass, but if you glue in a flange; you'd put a 45 on it and tape from underneath. I had previously measured and knew that the tank would clear the companionway with just over an inch to spare. I figured it had some hard miles on it but for 8K I bought it anyway. Cutting boat deck to replace fuel tank diagram. However, the leak is more likely to reappear compared to installing replacement fuel tanks for boats. Dobo, By any chance, have you contacted Novurania and asked them for advice and for a solution? The next day I removed the access port on the tank and got the remaining 3-1/2 gallons of "sludge" out of the tank and then washed out the tank with a hose and some heavy duty degreaser. Then it's a grinder or Circular saw with depth set to depth of deck.

1. Cutting boat deck to replace fuel tank diagram
2. Cutting boat deck to replace fuel tank on 2009 bmw 328i
3. Boat below deck fuel tank
4. Replacing boat fuel line to tank
5. Cutting boat deck to replace fuel tank.com

Cutting Boat Deck To Replace Fuel Tank Diagram

Engine: Toh1 3, 5 Yam 90/2S. Next to or over them? From the site: "Simply remove your tank, drain the fuel, swish a 50% mix of CLR and water around for about the length of your favorite Rockabilly song and then drain with a final swish of denatured alchohol. How to remove a below deck fuel tank. Converting the "T" shaped water tank would serve to eliminate that problem, but that tank contains the majority of the water supply on the boat. Yard J, Johanson Boatworks in Rockland ME, was the yard I chose. It never happened but will cost you. After cleaning and phospho-tizing the inside I sprayed the sealant all around the bottom, sides and interior of the center section between the baffel's... everywhere! When the removal is more challenging and time-consuming, the higher the end cost.

Cutting Boat Deck To Replace Fuel Tank On 2009 Bmw 328I

Once in the main salon, I removed the fittings from the tank and then, with help, took it out of the boat through the main companionway. I'm trying to figure out how to remove it. Taking to a petrol sodden deck with an electric angle grinder is likely to have a more sudden and catastrophic effect on the value of the boat. Also no large gasketed inspection port where the fuel pick ups attach. Contact: Photobucket doesn't place nice nice with the rest of the world... Cutting boat deck to replace fuel tank on 2009 bmw 328i. consider using the forum gallery. A guy here makes them 3/16" and glasses the entire top.

Boat Below Deck Fuel Tank

Whether big or small, unfortunately, aluminum boat fuel tanks have a limited life span and require replacement especially when exposed to harsh salt environments. Before I commit to the quote I would like to fell better about the dimensions. Join Date: Feb 2014. The large water tank is 93 gallons and is under the floor (sole) of the main solon. Foam sides of tank in place to prevent abrasion. The U. S. Coast Guard is the agency that establishes marine fuel-tank regulations. But a check of the hoses, clamps and filter revealed no cracks or leaks. Cutting boat deck to replace fuel tank.com. Moisture in the tank can be controlled by fuel polishing, either with chemicals or with mechanical flushing systems. Just from what I can see the sole does not sit on the stringer or baulkheads other than where they added putty when putting the cap in. Not to mention the associated engine trouble if salt-water enters the engine).

Replacing Boat Fuel Line To Tank

Their estimate was by far the most detailed. It is nice to have such large water storage if you plan long range cruising. Same goes for the fuel gauge sender and the wiring. I got off at a decent price knowing the fuel tank needs replacement. I was wondering what was used for ballast. Fuel and Water Tank Replacement in the Bilge. Hey folks, hoping to get some advice on a good way to remove a part of the cockpit deck in my Ellis 28. Since the repair we have logged over 25K nautical miles of travel in the boat, the majority ocean miles, finally stopping in mid1995 to build a shore based residence and then, after one more Bahamas cruise lasting nine months, refurbish the boat after 11 years of living aboard and cruising the east coast and islands extensively. It's easier to make water than take on fuel when you are out on the briny. Removing the Old Fuel Tank. Moeller Marine Products is the chief supplier of poly tanks for both original builders and aftermarket replacement. I'm going to order a new one from the original manufacturer RDS. The process is long and tedious, resulting in high labor costs when compared to the parts required to complete the installation. Cook says Moeller can also build custom tanks to add more fuel capacity or fit unusual mounting requirements.

Cutting Boat Deck To Replace Fuel Tank.Com

So I called the original Mfg from their label on the tank, they are still in business and after looking up the drawings for the tank( it is not in production any more) they gave me a price of $771. Thank you for your input. Stopped in to plan some projects. When I put the tank back in the boat, it cleared the companionway with 1/2in to spare. Above I mentioned Johanson had estimated based on removing the port and starboard setees, the gally up to the refrigerator and the nav station along with the cabin sole beneath each of these. My boat is a 1981, and it is on its third tank. She worked through the main engine access doors. In the finished installation we are now able to access the tops of the tanks. Fuel Tank Replacement - Key West 1994 1720 CC Sportsman. I have pictures of the whole deal somewhere, and can scan them in and send them to you as an attachment if you wish. In most boats the fuel tank is encased between the hull and the deck and there is no means to access it, unless you separate the two or cut a big hole in the deck.

Use oscillating tool to find corners. To remove the tanks, I found it easier to simply cut off the top of the tanks, cut out the baffles, make a cut down the corners (these cuts made with a jigsaw with a metal blade as well as a sawzall with a 12" rescue blade (they tell me it is supposed to cut anything) and simply collapsing the sides of the tank in and away from the foam which surrounds the tanks. I enthusiastically recommend Johanson Boatworks in Rockland, ME. Anyways, im thinking of setting the depth on my skil saw and starting small until I can expand my hole large enought to remove the tank and land half way on a stringer so I can place new wood and fiber glass later... Our solution to the new tank replacement was to use four tanks instead of the standard two. Like any boat project there were some complications.

Mon, 20 May 2024 05:11:12 +0000