Hi-Tek Bullet Coating Vs Powder Coating Powder

With ventilation comes temperature control. Mike is right about the CLAY. You can speed up the drying process by using a fan to blow onto the bullets, but don't rush it; the bullets need to be fully dried before they are baked. Q: How fast can these bullets be fired?

1. High tech bullet coating
2. Hi-tek bullet coating vs powder coating near me
3. Hi-tek bullet coating vs powder coatings
4. Hi-tek bullet coating vs powder coating kit
5. Hi-tek bullet coating vs powder coating spray
6. What is hi tek bullet coating
7. Hi tek bullet coating review

High Tech Bullet Coating

Looks like I need to cast more bullets! On the other hand, once Xlox hardens, I don't deal with that mess or the chance of lube migration into the powder and the process of selecting, cleaning, and tumble lubing means more opportunity to cull out bad bullets. I haven't figured out how to tell when the bullets are dry. I do not shoot matches or indoors. Whatever your preference is, just make sure your primer is seated deep enough so that it does not protrude the primer pocket. HI-TEK-LUBE COATING, POWDERED VERSION and Pure Acetone, or M. E. K. Powder Coated Bullets + Black Powder - SASS Wire. 2. An open garage door and some fans are not a bad idea.

Hi-Tek Bullet Coating Vs Powder Coating Near Me

What you are doing is seeing if the acetone will redissolve the coating. 560 +/- For IPSC Hi-Tek 2-Extreme Coating hidden puff bar bundle The powder did not stick. They were developed and are used in Europe more than here due to the regulations banning TGIC for health reasons. Oven baking temp, and bake duration are critical criteria. Also antimony (used to make lead harder)is twice as hard as barium. I have a ton of already traditional lubed bullets and that's how they will go down davis wrote:My issue with tumble lubed is that they have to be lubed and sized before tumble lubing. This was off sand bags at 25 yards. Hi-tek bullet coating vs powder coatings. My nose must not be as sensitive as others, or I'm just used to it. Color: Size: Each kit contains instructions, coating and the proper amount of catalyst required. My first try with a coated lead bullet was with a C9 3. Leading can have a detrimental affect on accuracy, and in the worse cases can lead to high pressures.

Hi-Tek Bullet Coating Vs Powder Coatings

You didn't miss it... it just arrived.. Whatever we deny or embrace. Dave's testing protocol is impeccable, so it must of been something with variations during loading. 380" for optimal results. It's good enough for me to shoot, but not something I am ready to sell (If I were to do that).

Hi-Tek Bullet Coating Vs Powder Coating Kit

What load/velocity worked for you? The coating separates in the bottle pretty quickly, so you'll need to shake it well to make sure it's mixed. At the time of publishing, the BPJ bullets were at least R150. The coating does not release any toxic gases or particulates during the firing process. 1gr difference in charge weight does not have a large enough difference to be a deciding factor on my own load development. Hi-Tek Coating Cast Bullets | The Ballistic Assistant. Even though I felt like I was hitting that 400 deg target temp, the bullets came out pretty dark.

Hi-Tek Bullet Coating Vs Powder Coating Spray

While one batch of 250 is baking, it takes another 20 minutes to shake and stack another 250. The only difference was 1/2 the bullets were lubed vs pc'd from the same lot/casting session of cast lead bullets. Any way you cut it, bullets coated with a chalk(chalk line powder) is an abrasive. I was talking with the owner of Hunter Supply David and he was tell he has a newer clear powder coated bullet for to market to get them in production for are air rifle and he is doing powder burner too he say it pick up fps and no leading your barrel he going to have 22 - 6mm -6. Mahi-Mahi, BOOYAH 60-Strand Ultra Fine …Who is J-Ames BULLETS®? 4 ounces) of acetone. But I like the idea of not having to wash off the lead when coming in to eat, or wearing something over cut hands, no cleaning of wax lube material from the dies, less junk to breathe at an indoor range to name a few benefits. Hi-Tek Versus Traditional Wax Lube. Over all the test of target and full loads with different OAL tossed in. I just wipe off the feed ramp, breech face, and back of barrel that contacts the breech face, and never touch the bore any more.

What Is Hi Tek Bullet Coating

Coating too heavily and/or inadequate dry time before placing in oven. Joy2shoot wrote:I am sorry you find it hard to believe, but I heard it first Eulette wrote: Based on all my years of shooting cast bullets with various lubes I've just never heard of that or experienced it. Should you fail this test, pop the bullets back in the oven and bake for a bit longer or check the temperature of the oven, in my case someone unplugged the oven. Location: Ridgefield WA. Shipping is now included in the price for every bullet profile!!! I am not a chemistry student, but I think of soft coal becoming a diamond through heat and pressure; and graphite similarly made into tough carbon fiber. The coating may change color slightly during baking, don't worry, it's normal. Location: Northern Illinois, USA. Thanks for the link, Harry. S148 wrote:maybe useful information here; Interesting article. What is hi tek bullet coating. Typically bullet lube is some sort of wax. I used a 308w that just got re-barreled and tested some loads with h335.

Hi Tek Bullet Coating Review

Thank you, ndownunder wrote:Hey Guys. Sized lead bullets may reduce adhesion of the coating to bond to. James r chapman wrote:Yep, those 'ol heel based lubed. Remember, it is better to use a little too much acetone and have VERY thin multiple coats as opposed to one thick heavy coat! With a case in the shell holder, turn in the die 1/8" at a time while raising the ram rod up to full stroke. Hi-tek bullet coating vs powder coating kit. I was slow to coated as an old time caster, but I'm pretty much sold on either HT or PC coated. J. C. Bell, SASS #15217 Posted September 21, 2021 Share Posted September 21, 2021 Are powder coated bullets and black powder propellant compatible?

45 and thought I'd never get the barrel cleaned out again... - Posts: 1052. This round is designed to be subsonic and travels slower than the speed of arlett's offers lead and Hi-Tek coated bullets for cowboy action shooting and other shooting disciplines! It will go on very thin, and the color will develop some in the oven. Read the details below before starting. If you need to flare more, turn the die in 1/8" until desired flare is obtained. Anyway just another opinion on what I've found with lubed vs pc'd bullets from a 30+ year bullet caster/swager. Brownells is your source for Hi-Tek Coated Hard Cast Flat Nose 224 Valkyrie 458 SOCOM Rifle Ammo, Ammunition at Brownells parts and accessories. 45 ACP 185 Grain Semi Wad Cutter - Red Coated - 1000ct. That's as good as I've gotten with anything else, including JHP, which is normally the most accurate.

Sat, 18 May 2024 02:03:41 +0000