Massey Ferguson 35 3 Point Hitch Won't Lift

Set quadrant levers. Is this DVD a Hollywood blockbuster with specail effects, highly paid film stars and a multi-million dollar budget? The guide is also of interest if you just want to understand how the system works and watch how the repair is done. Massey Ferguson 35 3 point lift arms raise but doesn't drop #1. Relief valve blows when Position control lever is in transport position. Massey ferguson 35 3 point hitch won't life music. StartVideo 6: System Overview and Troubleshooting (6:59). Remove and adjust the draft control spring. The superb hydraulic system on the Massey Ferguson 35 was integral to the model's success. The lift arms immediately lifted upon starting the engine and the pump continued to try and lift further. E C, Co. Cork, Ireland.

1. Massey ferguson 35 3 point hitch won't lift parts
2. Massey ferguson 35 3 point hitch won't lift rental
3. Massey ferguson 35 3 point hitch won't life music

Massey Ferguson 35 3 Point Hitch Won't Lift Parts

Right at where the draft response range starts. I bought this tractor a month ago and the previous owner used the left lever on the 2 spool control valve in front of the seat to lift and lower the 3 point hitch. Moncton, New Brunswick.

Close-up camera shots show the procedure in step-by-step detail, which makes it possible for anyone to undertake this repair. But as the top link spring had much play and the boot was dried out and cracked we decided to remove the lift cover and replace the spring, and rubber boot along with a new nut as the entire spring assembly needed be serviced and adjusted as per the Service Manual. MF35 Hydraulic Lift Not Working Properly. Set linkage arm drop rate. Restore the system to its original condition. I replaced the lift cover. What people have said…. StartVideo 4: Refitting Top Cover, Draft Control Spring (18:57).

Massey Ferguson 35 3 Point Hitch Won't Lift Rental

Thousands of people have watched Ian's tractor maintenance videos. My son and I now believe that we can take our tractor Hydraulics apart and put it back together again! We replaced the O-rings on the stand pipe and put a new one on the new cover plate. Click here to see what we've got! When you move the lift lever it seems to be working ok but in the wrong direction. System not operating as it should be doing. The lever pushes the control valve lever back, when you raise it. MF 35 lift arms won't lower - TractorByNet. Which way is the control valve lever supposed to move to raise the lift arms? No need to buy a workshop manual. Troubleshooting the fault.

Replace the rubber cover on the draft control spring. Regards, Steve Ridsdale. First job is to get one of those brackets made so I can remove the top cover on my own. Set safe transport height. Let us know how you get on with the above suggestions. Evidently the hydraulic fluid is being pumped into the standpipe as the lift piston is working. Massey ferguson 35 3 point hitch won't lift parts. The guide shows you everything you need to know, but for some further advice and information on the hydraulic system that's not contained in the film, then visit our additional hydraulics information page. 1959 MF 35 with 2 spool valve with levers in front of the seat.

Massey Ferguson 35 3 Point Hitch Won't Life Music

I'm guessing there was a problem with the control valve or something at that time when locking the left lever back did not allow the quadrant levers to work. I bought the video you made and it was very helpful. What should I do next to troubleshoot this issue? With over 30 years experience repairing tractors, Ian is the head mechanic at Vintage Tractor Engineer.

Chuck Harrison, USA. If you understand how a mechanical system works then you can usually diagnose the fault. I read something about an oscillator but have no idea where to look or how to check this. Assess and set the position and draft control linkages. Massey ferguson 35 3 point hitch won't lift rental. The lift arms drop after the engine has been switched off. Everything is shown in easy to follow step-by-step detail, so you can freeze-frame, rewind and watch the whole thing over again. We lowered the lift cover with a chain hoist making sure the Position and Draft levers were in front of the roller of the vertical control valve lever. It doesn't matter where we move the quadrant levers. We added new hydraulic fluid to just below the bottom bolt hole on the dip stick cover.

The control valve should move forwards towards to raise the lift (i. e. the top of the control valve actuating lever should move backwards). This seems to be the wrong way. I made sure the draft was set at the sector position between the little dots on the quadrant. I really didn't have much hope that a DVD would help me with this repair, but I am 100 percent satisfied with my purchase!!! The pressure caused fluid to leak out by the valve levers in front of the seat.

Sat, 18 May 2024 14:57:37 +0000