Harbor Freight Dust Collector Impeller Upgrade

Based on space and anecdotal evidence I went with the Thien. We do NOT want the impeller to start moving while our hands are in there! Make sure that if you use masonry anchors, the screws are long enough to fully engage the anchor. This proved an effective adapter. Rotate the impeller several times insuring no operational interference.. - Match original flange to new flange back to back. The bottom plate needed to be about an inch wider to sit on the trash can properly. This actually filters the dangerous dust, AND provides superior airflow. 16) 5/16" fender washers. HARBOR FREIGHT DUST COLLECTOR UPGRADE W/ SUPER DUST DEPUTY XL. I painted just the body of the gates and the handles. Larry Blighton Posted November 18, 2019 Report Share Posted November 18, 2019 I purchased a Harbor Freight dust collector and intend to upgrade the impeller. There are 2 that I know of, one from Rikon that has been next to impossible to get, and when available costs almost as much as the dust collector, and one from Wen, the 3403-22 Turbofan.

1. Harbor freight 2hp dust collector impeller upgrade
2. Harbor freight dust collector impeller upgrade kit
3. Harbor freight dust collector impeller upgrade your flash player
4. Harbor freight dust collector impeller upgrade parts
5. Harbor freight dust collector impeller upgrade

Harbor Freight 2Hp Dust Collector Impeller Upgrade

So, I started the upgrade by removing the 5″ DC hose and the connections at both sides. The jig ensures each pass is aligned. Since the flex pipe is exactly 4" it won't fit over the 4" PVC.

Harbor Freight Dust Collector Impeller Upgrade Kit

It's recommended to fasten joints with screws rather than glue so you can open the system easily to dislodge jams. The inside clear height is 4. I am looking to get more airflow out of the DC and am wondering about an impeller and output upgrade, and have some questions... #1. I used EVA foam to fill the gaps from the 2. Tool List: table saw with crosscut sled. 5" hole for coupler.

Harbor Freight Dust Collector Impeller Upgrade Your Flash Player

While I used (4) threaded rods to space the top and bottom, doing this again I might have just used wood posts around the perimeter. I used duct tape to increase the tension fit as needed. The blades are 1/4" with 1/2" MDF handle glued on one side and 1/2" MDF handle screwed on the other side. After cleaning up my shop (and a lot of dust), I decided to add dust collection.

Harbor Freight Dust Collector Impeller Upgrade Parts

The suction is great! Whether I do depends on whether/how much I get shocked. This ensures full close or full open when the handle is flush with the body. I considered attaching springs to hold the baffle to the trash can, hooking to the can's handles and drilling a hole into the bottom plate. Starting with the impeller and flange upgrade. At a few gates I have a 4" to 2.

Harbor Freight Dust Collector Impeller Upgrade

I sanded them lightly with a sander until the fit was better. Using proper PPE drill the holes. I used a round file to smooth out any rough cuts from the circle jig. As you can see from the above picture there is a grinder.

To determine if you have a 20 amp receptacle, they have a horizontal slot branching off one of the vertical slots. If you use coarse screws for PVC connections, this also allows for tying in grounding. While my breaker box is labeled, I also wrote the circuit on the actual duplex receptacle box as well. I ordered the RIkon impeller and with shipping it was $119.

5" flex pipe, not realizing the mismatch in size. Removing Current Impeller. Nicer ones are more expensive, but you can build your own that work well and don't break the bank. I marked the diameter of the HVAC connection and drilled a hole with 5/16″ bit to start the jig saw blade. Harbor freight 2hp dust collector impeller upgrade. It's a 12" impeller with reverse vanes while the stock HF impeller is 10" with forward vanes. My old 35A uses tiny turnbuckles on the inside to hold it in place. Remove the original bag filter, and support bar.

A total of 8 srews holding it on. I had considered making homemade PVC tapers, but didn't. It's also one extra step before I cut anything. I have a cyclone for chip collection, it works well but I do end up with a few inches of fine powder in the bag after a few weeks of running. It was also a bit looser fit than I anticipated, but held on there. It snapped trying to fit it to a 17" diameter.

Sun, 19 May 2024 06:03:01 +0000