Tattoo Shops In Wisconsin Dells

Tattoo Shops In Wisconsin Dells

Oil Cooler Torque Specs

If anyone thinks the internet is serious they should seriously log off and burn their laptop. 9L IDI engines may require (4) small o-rings and (2) large o-rings. Ford E3TZ-6A636-C. Rear oil cooler header to engine block gasket.

7.3 Oil Cooler Torque Specs Review

Engine over until you see a bolt or plug. During the repairs we will include. If everything is correct the bolts should screw. Rear bracket to frame mounting nuts. 3L Power Stroke engines use "A" code injectors, which feature a 16. 3] Oil cooler headers are becoming obsolete and primarily available through obsolete part dealers in the form of NOS replacements. I take out the bolts on the drivers side, they are easy since I removed the battery tray. Front oil cooler header to engine block gasket.

7.3 Oil Cooler Torque Specs Guide

I get the cooler side finger tight as were the instructions I got from here, expecting it to dribble some and I could tighten until it stops leaking. They will likely be hard, brittle, disfigured, and possibly broken. Begin reassembling the pan back onto the transmission. Follow along for the tips and tricks you'll need to know to tackle this fairly straightforward job in your own driveway. To do this you can either siphon the fluid out using the trans cooler lines. Now see and access the transmission filter, when removing be sure that the o-ring comes out with. Cap the nipple and hose as to reduce fluid loss while the pump is being removed. The first 2 digits of the serial number are "7. Over time, an oil cooler seal can fail due to wear or age. 3L Power Stroke diesel V-8. The molded in orings aren't very thick and don't look to be too forgiving!

7.3 Oil Cooler Torque Specs

We left the bolts loose until the rear gasket (PN F4TZ-6A636-A) and rear section of the oil cooler was reattached. • Check for coolant and oil leaks around the oil cooler headers once more. Ford F-550 Super Duty V8 (7. I am not sure if I should back them out and retorque them since I already smashed the gasket or if this will cause a problem at all?

7.3 Oil Cooler Torque Specs Vs

Location: Western Michigan(by the lake). 18 ft. pulley mounting bolt. • Clean and prep the oil cooler for new o-rings - begin by cleaning any debris from the heat exchanger tubes. 1997 model year engines designed to meet California emissions standards (CARB certification) feature AB split shot injectors, NOT AA. 3L Power Stroke Transmission Options. If you do not have access to a press, you can get creative with a floor jack, porta-power, etc. Connecting rod cap nuts Stage 1. You can properly torque about 4 of the 14. Then the pan is properly in place. The inner O-rings carry Ford part number 1C3Z-6C610-BA, the outers are PN 1C3Z-6K649-BA and they can be had in all-inclusive oil cooler re-seal kits for between $60 and $80.

9L IDI engines may have a rare six o-ring oil cooler. Aspiration: Single turbocharger, wastegated, intercooler introduced for 1999 model year. Intake manifold cover mounting bolts. The rear header has an indentation in which the tab on the heat exchanger must insert into. • Completely remove the 14mm and 16mm power steering pump bracket bolts, then remove the power steering pump and set aside. The pan bolts should be torqued to 10 ft-lbs. Oil level indicator tube adapter nut.

Transmission from the vehicle. If all went well, your 7. The main cause of oil leaks from the oil cooler hoses is the usage of the wrong crush washers. Location: Stillwater, OK. Member`s Gallery. I check my oil, it is full, let's crank the car.

Clean the sealing surfaces. You should be using aluminum washers. Well, you don't use a screwdriver much on this car, right? • While cleaning, use small pieces of a clean rag to keep debris from entering the oil and/or coolant passages. What are the torque specs on the following: Injector retainer... 28 lbs. To start viewing messages, select the forum that you want to visit from the selection below. Exhaust manifold mounting pipe nuts and bolts. First thing's first, I lay out my parts. Injection: Direct injection, HEUI (hydraulic electronic unit injection). Width: 32" (approx). But now, NOW the cooler should be free!.. Just so happen to have a 2002 caddilac escalade (HD, same egine as truck) (going to swap engine into e30) that uses the same radiator as the truck. I lay the old cooler and lines next to the new one and compare, to make sure they match. By the beginning of the 2004 MY, the 6.

Tue, 18 Jun 2024 07:04:35 +0000