Fuel Pump Access Cover For Truck Bed

The pump gets hot and boom fill it with a bunch of cold fuel. If you only change the pump and not the sending unit, you chance having to go back in because of a sticking check ball. The last time I replaced my fuel pump in my 97 c1500 with 4. Sent from my DROID RAZR MAXX using tapatalk 2. What To Do With This? (Hole in Truck Bed Above Gas Tank. So taking off the bed and leaving it at my house is out of the question. Register and never see these ads again.

1. Where to cut hole in truck bed for fuel pump
2. Fuel pump cap removal tool
3. Where to cut hole in truck bed for fuel pumpkin
4. Where to cut hole in truck bed for fuel pumpkins

Where To Cut Hole In Truck Bed For Fuel Pump

2001 Ford Ranger Supercab (4dr), Oxford White, 4. Pump is located in relation to the truck bed. This is a ratty truck anyway and I couldnt care less about what it looks like. 3L 4 CYL... SIDE STEP BABY.... (and running hotter than hell). Re: 1997 GMC K1500 fuel pump and sending unit replacement. Once you have the module back together, do yourself a favor and a) lube the gasket on the tank with a solvent-based lube like Marvel or WD and b) put that screw ring on BEFORE you put the pump in place, much easier to do out of the truck. I removed the rear bumper to make sure I didn't scratch the bed, then I just loosened the passenger side bolts, removed the drivers side bolts, and used a ratchet strap between the front and rear corners on the drivers side and my engine hoist to lift the drivers side up and hold it. Where to cut hole in truck bed for fuel pumpkins. Location: Binghamton, NY.

Fuel Pump Cap Removal Tool

Has anyone done this? Hope this helps with any other onlookers! 00 each), N806251/S103 for the 4 shorter bolts ($14. Since this is the second pump to go in less then a year... Other Fords owned: 00 Taurus, 96 T-Bird, 95 Escort GT, 93 Mustang 5. Great write up and picture. The fuel pump is one of them. Just a quick update, I've been about 2000 miles on my replacement pump, going over the best (meaning the worst) frost heaves that backwoods Maine can provide (you know, they type that you get air off of it you hit them more than 30mph) with no issues. Where to cut hole in truck bed for fuel pump. Everything should go together in the reverse you took it apart. Users browsing this forum: Google Mediapartners and 7 guests.

Where To Cut Hole In Truck Bed For Fuel Pumpkin

Blood type; Retumbo. 2004 Ranger, Ext Cab, 2WD, 3. This must be the question of the week... if it is a KC, there is a support channel in the way, you need more room than you think to pull that pump STRAIGHT up. 1996 chevy k1500 reg cab 4x4(daily driver)totaled. So I carefully measured and drilled two pilot holes from underneath to locate the hatch, then cut out the floor with a grinder. Tuck it out of the way. I have to admit I read the entire was very laugh out loud funny but I did chuckle a few times along the way................ If your a CC, cutting a hole in the rear of the cab, really?. Cutting an access hole in the bed to inspect a problem with the fuel tank, fuel is the epitome of jury rigging. Fuel pump access cover for truck bed. Location: Val-Des-Monts Quebec. It is easier to take the bed off of the truck than it is to lower the tank. Ford part numbers are: N806252/S103 for the 2 longer bolts ($13.

Where To Cut Hole In Truck Bed For Fuel Pumpkins

Is the pump dead center of the tank? For safety sake, don`t be lazy just remove the tank, run it down, siphon it out, whatever. Hmmm... Can just 2 guys lift the bed off? We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to and affiliated sites. Cut hole in floor to access fuel pump. This thread is hysterical! Where can I find a diagram showing where the fuel. The top part has two cutouts. 1997 4WD Chevrolet Silverado Extended Cab Short Bed (purchased new January 1997). I have a 2016 GMC Sierra 1500 crew cab 5. What is hilarious to me is people that have love affairs with machinary. Im going to stew on it awhile and do some more research. Do yourself a favor and use the right tool ($10 at FLAPS) instead of your fingers or a pair of pliers.

So I would have to find a place to do it AND store it. I've read 3 screws but mine has 4. the top one SUCKS, use a LONG THIN #2 phillips unless you like stripped heads. Where to cut hole in truck bed for fuel pumpkin. If I fill the truck up with gas it will run great then start the same no power high gas usage issue, If topped of it will leak a tiny tiny bit but only briefly its not a steady thing.. You will have to cut off your old one and hook up the old one. Now, you have to fight with the big ring that holds the module in. Also wanted to get an idea of how big a hole and where it should be.

Made the next one a lot easier and quicker. In case you break a bolt-. Replaced many over the years. Then replace the metal brake line between the tank and frame. DO NOT DROP THE TANK!! 5, 5 speed, 2WD, no AC, 150k (SOLD). Jack that puppy up (down but up cuz it's upside down). 1970 4WD Chevrolet Suburban. Get an old-school bumper jack, you know the type with the LONG toothed shaft and the jack part that clicks up and down it. So this is my next guess. My bed was starting to rust so I didn't care about cutting it, now it's so easy to get to. While you're taking care of your truck's maintenance needs, take a moment to review its insurance coverage. Also I live in a community where working on you vehicle period is forbidden. Switch to the other cut out and disconnect the electrical connector.

Sun, 19 May 2024 03:26:10 +0000